Most people in their apartments and houses have furniture their laminated chipboard or MDF. Since these are pressed slabs, if damaged, the defective area looks simply terrible and greatly spoils the appearance. Let's look at how you can repair the damage and hide its traces.
Pasting large torn laminated pieces
Torn pieces from the stove can be glued with PVA glue, covered with cling film and pressed with a clamp through the slats until it dries.
After gluing, the seam can be rubbed with a wax stick of the appropriate color. If it is a white body, it is enough to cover it with a regular corrector from office supplies.
Restoring a hole for a self-tapping screw or confirmation
If you need to repair a large chip and restore the space for fasteners, you can use epoxy clay or cold welding.
The composition is mixed and applied in place of the torn piece. In this case, you need to glue the fallen fasteners back into place.
Before the composition becomes hard, it needs to be trimmed by cutting off the protruding part with a blade.
You can also smooth it by pressing it with an even strip through a plastic bag. Immediately the field of this fastener is unscrewed.
When everything has hardened, you need to sand the surface and paint it in color with a corrector or oil paint. If during further assembly the line of contact between the intact and the restored part is noticeable, the corner can be rubbed with a wax pencil
Filling a chip with a 3D pen
The chip needs to be primed with PVA glue. Then a couple of staples are driven into the part, but so that they protrude slightly.
After the glue dries, the damage is filled with polymer from a 3D pen.
Next, the plastic is ironed through parchment paper, and the excess is cut off with a blade. You can also sand the defect and paint it.
Repairing small chips of the laminated layer on the edges
If there are small chips on the edges of the chipboard after cutting, it is enough to move a wax pencil with a selected color along them. On white parts, a corrector helps.
Repairing a through hole from a long self-tapping screw
If, when assembling furniture, a self-tapping screw was screwed in too long and it went right through, it must be unscrewed immediately. The chipped particles of the laminated layer are pushed aside, the sawdust is washed off, and glue is applied. Then you need to put the flaps back and press with a clamp until dry.
If the flaps are lost, the problem is solved with wax. It needs to be pushed into the hole with the tip of a knife and trimmed.
Restoring scuffs and dents on PVC edges
When the PVC edge has scuffs or dents, it is enough to polish it with the laminated part of a piece of fiberboard. If the tone of the PVC in the restored area is lighter, it needs to be heated with a hairdryer and it will become darker.
Repairing bent plastic parts
If the tray under the dryer is bent, you need to heat the bend with a hairdryer and hold it in a leveled position until it hardens. Heating can also restore the color and hardness of the plastic corner. If it has been bent, you need to blow it with a hairdryer until the white bend line matches the color of the rest of the plastic.
Extension for a torn door hinge
To securely restore the hinge fastening, you need to buy a mortise furniture nut with a screw. It is glued to the place of the removed screw. To do this, use a mixture of epoxy resin with ordinary dry gypsum putty, fine sawdust or other filler. To prevent the compound from getting inside the nut, it can be filled with grease.
Next, formwork is placed on the damaged facade, and it is filled with the composition in several passes. The hole for the hinge can be opened with a ring of PVC pipe.
If the edge on the façade was severely damaged when the hinge came off, it will have to be replaced. It's better to take a self-adhesive one. It is heated with a hairdryer and pressed.
The excess width of the edge is cut off and the cut is ground.
The surface restored with epoxy is filled with corrector or oil paint. Then the loop returns to its place.
