Do it yourself
Life hacks, master classes, useful tips, recipes.
home » Different » Crafts » Origami » Rosebud made of corrugated paper
Corrugated paper has its own special properties, thanks to which it can be used to make charming flowers that will be an excellent imitation of living specimens.

Corrugated paper rosebud


To make such a bud you will need for work:
Material:
- thick corrugated paper in the following tones: green and pink.
- wire.
- a small lump of cotton wool.
Tools:
- scissors.
- tweezers.

Making a flower. First of all, from a piece of pink corrugated paper you need to use scissors and a ruler to cut out a regular rectangle with sides of 6x7 cm, it is important to make sure that the part is not skewed.

paper


Then you need to round the two top corners and mark the pointy top at the center.

Making a flower


Now you should cut 15 cm from the prepared fishing line. You need to take one edge of the resulting piece and bend it around your finger, creating a small ring and freeing your hand to secure the wire in this form.

Making a flower


Next, on the pink part in its middle, you need to place a ring of wire and a small piece of cotton wool. It is needed to obtain the fullness of the bud and facilitate its creation.Now you need to use the right rounded corner to wrap the cotton wool and wire folded in the center. At the intersection of the cotton wool and the paper, you need to slightly stretch it.

Making a flower


After this, you should make the same fold, but on the other side.

Making a flower


Next you need to fold the bottom part of the resulting bud very tightly. To do this, it is best to twist the paper around the wire with your fingers, the tighter the better.

Making a flower


Now you can start creating leaves. To do this, you need to cut out a large rectangle from green corrugated paper, the sides of which will be 6x9 cm.

Making a flower


Next along the longest side of this part you need to make many zigzag cuts.

Making a flower


After this, you need to wrap the prepared foliage around the base of the made bud. The lower part should also be tightened tightly and, to ensure secure fastening, it is better to tighten it with wire.

Rosebud


From the remaining piece of green paper you need to make a straight strip 3 cm wide and about 15 cm long and wrap it around the wire. Using this strip, you need to cover the base of the bud and gradually wrap the wire at a 45 degree angle, creating a flower stem.

You need to carefully twist the long parts of the leaves that touch the bud with your fingers.

Corrugated paper rosebud


Now the rosebud is ready. These flowers can be used to make a very attractive bouquet!

Corrugated paper rosebud
come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
4 minus one =
Comments (0)

How to make a machine from rotors from electric motors for quickly stripping insulation from wires

Painting on a gramophone record | Do it yourself

Elegant jars for the kitchen | Do it yourself

How to quickly clean battery terminals

«Do it yourself - with your own hands» - a site of interesting homemade products made from scrap materials and items at home. Step-by-step master classes with photos and descriptions, technologies, life hacks - everything a real master or just a craftsman needs for needlework. Crafts of any complexity, a large selection of directions and ideas for creativity.

We recommend reading

Washing machine error codes