Do it yourself
Life hacks, master classes, useful tips, recipes.
home » Electronics » Electronics from China » How to make a power regulator for household appliances

Anyone can assemble such a simple regulator. Knowledge of electronics will not be required, since a ready-made Chinese module will be used, which can be purchased for a very small amount. With all this, the regulator is capable of regulating the power of devices up to 2000 W.

The regulator can be used to regulate the power of any electric heating devices, various engines, power tools, etc.

Will need

Making a power regulator

We disassemble the junction box by removing the top cover.

We take the socket and disassemble it in the same way.

We unscrew the side fastenings so that they do not dangle. They won't be useful anymore.

At this point, you don’t need to do anything else with the outlet.

We drill a hole in the cover of the distribution box for the socket.

We install the socket in this socket and secure it with self-tapping screws.

Using a step drill, we make a hole in the side of the box for the wire bushing.

We insert the bushing and secure it with plastic nuts on both sides that come with the bushing.

We pass the wire through it.

Now it's time to connect the module. It's not difficult, here's the diagram:

We connect the stripped wires of the network cable to the screw terminals. And also screw a piece of wire to connect to the outlet.

We connect the wires to the contacts of the socket.

Using a stepped drill, we drill a hole on the other side of the box for the variable resistor of the module board. It will also hold the entire board in the case.

We insert the variable resistor into the hole and secure it with a nut.

We put the handle on the shaft.

Close the lid of the box and assemble the socket.

We screw the sleeve, thereby fixing the wire.

We tighten the four screws of the box. At this point the regulator is ready.

Checking the operation of the regulator

We turn on the network, connect the light bulb. Everything is adjusted very smoothly, without any jumps or steps.

We are trying to connect the grinder.

I think it won’t be difficult to figure out how and where to use this: electric stoves, water heater heating elements, pump motors, etc. The thing is useful and necessary in everyday life.

Friends, follow all safety requirements. The tension that is present inside is life-threatening.

Watch the video

come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (11)
  1. Guest Alexander
    #1 Guest Alexander Guests 18 June 2018 22:54
    5
    Suitable for resistive loads. For engines - no.
    1. Guest Alexey
      #2 Guest Alexey Guests 19 June 2018 10:51
      0
      Why?
    2. Guest Mikhail
      #3 Guest Mikhail Guests 20 June 2018 15:02
      0
      Do you think grinders with a regulator have other dimmers? Exactly the same.
    3. anvar
      #4 anvar Guests 20 June 2018 15:37
      1
      due to the fact that the output current shape is not a sinusoid
      1. Sergey K
        #5 Sergey K Visitors 21 June 2018 13:12
        0
        So the grinder has a commutator motor, it doesn’t care about the sine wave!
  2. Guest Yuri
    #6 Guest Yuri Guests 19 June 2018 17:06
    0
    This is bullshit for nichrome light bulbs
  3. Anvar Aminov
    #7 Anvar Aminov Guests 20 June 2018 15:49
    0
    the current waveform is not a sinusoid
  4. Guest Mikhail
    #8 Guest Mikhail Guests June 21, 2018 09:58
    1
    It would be nice to know the characteristics of this device. Judging by its appearance, it is only suitable for low-power devices. Like turning the light down and up in a light bulb.
    1. Guest Mikhail
      #9 Guest Mikhail Guests 21 June 2018 14:45
      0
      The power of the regulator depends only on the used triac and radiator in case of heavy load.
  5. Guest Andrey
    #10 Guest Andrey Guests 21 June 2018 19:03
    1
    What is a wire bushing? I know the seal, pressure seal. And it works like a dissertation. The pump will not work, it will burn out, this is not a frequency converter
  6. Anton
    #11 Anton Guests 30 October 2018 14:23
    3
    You can install a regulator board from a vacuum cleaner, just for the engines.

Crafts from CDs | Do it yourself

Lava lamp | Do it yourself

Funny balloon toys | Do it yourself

What can you do with an empty plastic container?

«Do it yourself - with your own hands» - a site of interesting homemade products made from scrap materials and items at home. Step-by-step master classes with photos and descriptions, technologies, life hacks - everything a real master or just a craftsman needs for needlework. Crafts of any complexity, a large selection of directions and ideas for creativity.

We recommend reading

Washing machine error codes