Do it yourself
Life hacks, master classes, useful tips, recipes.

Construction and repair. Page 12

Master classes:

With this tool, you no longer need a hammer when hammering in posts.

When installing a light fence or tensioning a mesh, the posts do not have to be dug in or concreted, but driven in. It's faster and easier, but still difficult. If you have to drive in a couple of dozen pillars, then it’s worth welding a simple device for this,

How to mix an ultra-reliable oven mortar that does not crack

With the help of a heating and cooking stove, you can not only heat the room, but also cook food. However, the combination of materials such as brick, cast iron and clay (cement) with different coefficients of thermal expansion leads to cracking

How to waterproof wooden poles for centuries

When digging in wooden posts, it is advisable to waterproof them over the entire surface that will be in the ground. This will prevent the wood from rotting, so the pole will last many times longer.

How to build a cheap large pool from pallets in 1 day

When spending your summer vacation at your dacha, it’s not a bad idea to have your own swimming pool on the property. At first glance, building such a structure is not cheap and requires months of manual labor. In fact, you can make a large pool with your own hands in 1

We make a budget drainage system for the roof from sewer pipes

When building a house, such a small thing as a system for draining water from the roof is not much cheaper than the roof itself. It requires a lot of expensive little things that add up to a significant amount. To save money without losing quality and

How to make a grinder cut concrete without dust

When cutting grooves in walls, trimming bricks, cinder blocks, concrete and other mineral building materials, a lot of thick dust is generated. If the work is done outdoors, then this is still tolerable, but indoors there is an impenetrable dusty curtain

How to make a strong blind area yourself for many, many years

This type of work is quite physically challenging and requires preparation. But, if you try, you can do it yourself. First you need to decide on the size of the blind area. It is possible to make it wider on one side of the building, and

How to make decorative slate for decoration without a mold

Gypsum tiles imitating decorative stone can be used to decorate the portal of an electric fireplace, walls in the hallway, corridor, and kitchen area. This is a very easy-to-work material that is sold in every hardware store for

How to lay stamped concrete so that it is indistinguishable from tiles

If you want to lay paving slabs in your yard, it makes sense to think about choosing printed concrete. It is a monolithic slab with a reinforced top layer and decorative finishing of the front surface. It can imitate tiles,

A cheap foundation made from car tires in a couple of hours

The recently widespread technology of frame construction involves the use of columnar foundations. Frame buildings are so light in comparison with brick and aerated concrete that they can be used as a foundation

How to make your own acrylic putty

When making minor repairs or modeling certain items, sometimes a nuisance occurs such as a slight shortage of consumables. For example, putties. Well, we miscalculated a little! Or they spilled it, it doesn’t matter. For example, when gluing

How to make a textured roller to imitate bamboo using putty

To create a relief decor on the walls, textured rollers are used that roll over fresh putty. They imitate snake skin, tree bark, stone and even bamboo. The relief obtained with their help is painted with paints of different shades, which

Which fasteners to choose for foam aerated concrete. Homemade anchor

Gas blocks and foam blocks are poorly held by fasteners for concrete and brick - dowel-nails, anchors, screws, etc. This is due to the fact that porous materials cannot withstand point loads. But, drilling conical holes in them and filling them with durable

How to lay linoleum on a plank floor

Laying linoleum on a wooden floor is more difficult than laying it on a concrete screed. The boards can “play” and vibrate, which creates certain difficulties when installing a new flooring. But this is not a reason to refuse repairs. To eliminate sagging,

How to make a chimney for a bathhouse from sewer pipes

The installation of a chimney for a bath or sauna should be approached with all responsibility in order to prevent smoke from entering the steam room and not getting burned.

How to wash a foam gun for pennies? Let's make a useful device

Polyurethane foam today has become a permanent attribute of builders involved in installing windows, doors, etc. In the household, it is needed from time to time, which is why the problem of foam drying inside the gun arises. As a result, use it

How to unscrew a broken eccentric on a faucet

Eccentrics on faucets, especially those installed on a hot water supply pipe, can burst due to temperature or pressure changes. As a result, a stream flows out of them like a fountain, so the problem requires an urgent solution. The whole difficulty is that

How to remove a frozen plug from a tube with sealant

If, after opening a tube of silicone, you do not use it for a long time, the sealant may partially harden directly in the tube from the side of the spout. In this case, it will not be squeezed out, and if you try to force it through, you can bend or break the gun.

Laying laminate on the wall

Laminate is a common material used for flooring.However, today designers have begun to often use this material in wall decoration. This is a universal solution that is practical and

How to use silicone sealant from a tube without a gun

Typically, the sealants that we use in everyday life are packaged in hard plastic or metal containers and inserted into a special gun, which, when the trigger is pulled, is squeezed out of the tube. But how to use the remedy if under

How to remove dried cap from a tube nozzle and reuse the nozzle

If the silicone or liquid nails remaining in the can are not reliably isolated from contact with air, then they dry out in the cone of the plastic nozzle and form a very strong plug that cannot be squeezed out with any gun. Reuse them

Cheap and cheerful: finishing the base with cement mortar

The base is the part of the foundation protruding above the ground and is one of the most important elements of the building, which must be reliably protected from external influences and at the same time look aesthetically pleasing, since it is always in sight. It can be easily and at minimal cost

Free Junk Tile Cutter

One of the stopping factors for doing tile work on your own is the lack of a tile cutter. This is a fairly expensive tool, the purchase of which for one-time cladding is impractical. You can get out of the situation by making it simple and

How to open a silicone tube correctly to get the job done efficiently

Many craftsmen and builders are not even aware of this trick, which significantly improves the quality of your repair. For example, you need to apply silicone caulk to a corner gap between two surfaces to seal. If you

DIY pocket stove

How to quickly remove a stump on a site with your own hands

A simple and proven recipe for salted salmon

The simplest do-it-yourself sandblasting nozzle for a compressor

«Do it yourself - with your own hands» - a site of interesting homemade products made from scrap materials and items at home. Step-by-step master classes with photos and descriptions, technologies, life hacks - everything a real master or just a craftsman needs for needlework. Crafts of any complexity, a large selection of directions and ideas for creativity.

We recommend reading

Washing machine error codes